لیست کامل Code های مشکل یاب کامپیوتر به صورت پالس BEEP

[Varand]

سلام به همه دوستان عزیز و خوانندگان محترم

معرفی لیست کامل Code های مشکل یاب کامپیوتر به صورت پالس BEEP

همه ما می دانیم که Debuger کامپیوتر به دو صورت مشکل کامپیوتر رو به مخاطب منتقل می کند. یکی Buzzer که به صورت خط و نقطه (تلگرافی) مشکل رو اعلام می کند و دومی Debuger دو رقم دیجیتالی می باشد که اکثر مادر بورد های ساده از این debuger پشتیبانی نمی کنند. این بوق ها بنا به سازنده bios مادربورد معنای مختلفی دارد و اول از همه باید تشخیص داد که از چه Bios استفاده می شود

[Only registered and activated users can see links. ]


AMI BIOS beep codes

Beep Code	Descriptions
1 short	DRAM refresh failure
2 short	Parity circuit failure
3 short	Base 64K RAM failure
4 short	System timer failure
5 short	Process failure
6 short	Keyboard controller Gate A20 error
7 short	Virtual mode exception error
8 short	Display memory Read/Write test failure
9 short	ROM BIOS checksum failure
10 short	CMOS shutdown Read/Write error
11 short	Cache Memory error
1 long, 3 short	Conventional/Extended memory failure
1 long, 8 short	Display/Retrace test failed

AWARD BIOS beep codes

Beep Code	Description
1 long, 2 short	Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information
(Any other beeps)	RAM problem.

IBM BIOS beep codes

Beep Code	Description
No Beeps	No Power, Loose Card, or Short
1 Short Beep	Normal POST, computer is ok.
2 Short Beep	POST error, review screen for error code.
Continuous Beep	No Power, Loose Card, or Short
Repeating Short Beep	No Power, Loose Card, or Short
One Long and one Short Beep	Motherboard issue.
One Long and Two Short Beeps	Video (Mono/CGA Display Circuitry) issue
One Long and Three Short Beeps.	Video (EGA) Display Circuitry
Three Long Beeps	Keyboard or Keyboard card error
One Beep, Blank or Incorrect Display	Video Display Circuitry

Macintosh startup tones

Tones	Error
Error Tone. (two sets of different tones)	Problem with logic board or SCSI bus.
Startup tone, drive spins, no video	Problem with video controller.
Powers on, no tone.	Logic board problem.
High Tone, four higher tones.	Problem with SIMM.

Phoenix BIOS beep codes

Beep Code	Description and what to check
1-1-1-3	Verify Real Mode
1-1-2-1	Get CPU Type
1-1-2-3	Initialize system hardware
1-1-3-1	Initialize chipset registers with initial POST values
1-1-3-2	Set in POST flag
1-1-3-3	Initialize CPU registers
1-1-4-1	Initialize cache to initial POST values
1-1-4-3	Initialize I/O
1-2-1-1	Initialize Power Management
1-2-1-2	Load alternate registers with initial POST values
1-2-1-3	Jump to UserPatch0
1-2-2-1	Initialize keyboard controller
1-2-2-3	BIOS ROM checksum
1-2-3-1	8254 timer initialization
1-2-3-3	8237 DMA controller initialization
1-2-4-1	Reset Programmable Interrupt Controller
1-3-1-1	Test DRAM refresh
1-3-1-3	Test 8742 Keyboard Controller
1-3-2-1	Set ES segment to register to 4 GB
1-3-3-1	28 Autosize DRAM
1-3-3-3	Clear 512K base RAM.
1-3-4-1	Test 512 base address lines
1-3-4-3	Test 512K base memory
1-4-1-3	Test CPU bus-clock frequency
1-4-2-4	Reinitialize the chipset
1-4-3-1	Shadow system BIOS ROM
1-4-3-2	Reinitialize the cache
1-4-3-3	Autosize cache
1-4-4-1	Configure advanced chipset registers
1-4-4-2	Load alternate registers with CMOS values
2-1-1-1	Set Initial CPU speed
2-1-1-3	Initialize interrupt vectors
2-1-2-1	Initialize BIOS interrupts
2-1-2-3	Check ROM copyright notice.
2-1-2-4	Initialize manager for PCI Options ROMs
2-1-3-1	Check video configuration against CMOS
2-1-3-2	Initialize PCI bus and devices
2-1-3-3	Initialize all video adapters in system
2-1-4-1	Shadow video BIOS ROM
2-1-4-3	Display copyright notice
2-2-1-1	Display CPU Type and speed
2-2-1-3	Test keyboard
2-2-2-1	Set key click if enabled
2-2-2-3	56 Enable keyboard
2-2-3-1	Test for unexpected interrupts
2-2-3-3	Display prompt Press F2 to enter SETUP
2-2-4-1	Test RAM between 512 and 640k
2-3-1-1	Test expanded memory
2-3-1-3	Test extended memory address lines
2-3-2-1	Jump to UserPatch1
2-3-2-3	Configure advanced cache registers
2-3-3-1	Enable external and CPU caches
2-3-3-3	Display external cache size
2-3-4-1	Display shadow message
2-3-4-3	Display non-disposable segments
2-4-1-1	Display error messages
2-4-1-3	Check for configuration errors
2-4-2-1	Test real-time clock
2-4-2-3	Check for keyboard error
2-4-4-1	Set up hardware interrupts vectors
2-4-4-3	Test coprocessor if present
3-1-1-1	Disable onboard I/O ports
3-1-1-3	Detect and install external RS232 ports
3-1-2-1	Detect and install external parallel ports
3-1-2-3	Re-initialize onboard I/O ports
3-1-3-1	Initialize BIOS Data Area
3-1-3-3	Initialize Extended BIOS Data Area
3-1-4-1	Initialize floppy controller
3-2-1-1	Initialize hard disk controller
3-2-1-2	Initialize local bus hard disk controller
3-2-1-3	Jump to UserPatch2
3-2-2-1	Disable A20 address line
3-2-2-3	Clear huge ES segment register
3-2-3-1	Search for option ROMs
3-2-3-3	Shadow option ROMs
3-2-4-1	Set up Power Management
3-2-4-3	Enable hardware interrupts
3-3-1-1	Set time of day
3-3-1-3	Check key lock
3-3-3-1	Erase F2 prompt
3-3-3-3	Scan for F2 key stroke
3-3-4-1	Enter SETUP
3-3-4-3	Clear in POST flag
3-4-1-1	Check for error
3-4-1-3	POST done - prepare to boot operating system
3-4-2-1	One beep
3-4-2-3	Check password (optional)
3-4-3-1	Clear global descriptor table
3-4-4-1	Clear parity checkers
3-4-4-3	Clear screen (optional)
3-4-4-4	Check virus and backup reminders
4-1-1-1	Try to boot with INT 19
4-2-1-1	Interrupt handler error
4-2-1-3	Unknown interrupt error
4-2-2-1	Pending interrupt error
4-2-2-3	Initialize option ROM error
4-2-3-1	Shutdown error
4-2-3-3	Extended Block Move
4-2-4-1	Shutdown 10 error
4-3-1-3	Initialize the chipset
4-3-1-4	Initialize refresh counter
4-3-2-1	Check for Forced Flash
4-3-2-2	Check HW status of ROM
4-3-2-3	BIOS ROM is OK
4-3-2-4	Do a complete RAM test
4-3-3-1	Do OEM initialization
4-3-3-2	Initialize interrupt controller
4-3-3-3	Read in bootstrap code
4-3-3-4	Initialize all vectors
4-3-4-1	Boot the Flash program
4-3-4-2	Initialize the boot device
4-3-4-3	Boot code was read OK